Thanks to the quick-release thru axle, our wheels can be pulled out from the axle mount of the rear end with just one "click" or inserted again and locked securely. At the end of the quick-release thru axle is a ball lock pin, which is unlocked by pressing the aluminum cap and engages inside the axle mount in a milled groove. Axle diameter: 12 mm Total length: approx. 125 mm Weight: approx. 100 gMade from stainless-steelIncl. plastic spacer and rubber O-ring Suitable for all wheels of the axle system 12/20 (except wheel KU 12", here a shorter axle must be used)

Thanks to the quick-release thru axle, our wheels can be pulled out from the axle mount of the rear end with just one "click" or inserted again and locked securely. At the end of the quick-release thru axle is a ball lock pin, which is unlocked by pressing the aluminum cap and engages inside the axle mount in a milled groove. Axle diameter: 12 mm Total length: approx. 125 mm Weight: approx. 100 g Made from stainless-steel Incl. plastic spacer and rubber O-ring Suitable for all wheels of the axle system 12/20 (except wheel KU 12", here a shorter axle must be used)

So that the thru axle can not slip out of the hub of the wheel, it is held in position with a rubber ring. If the wheel is clicked into our plastic axle mount, a spacer is additionally required on the thru axle. When using the continuous stainless steel axles, only a rubber ring is needed. Spare part set for the axle system 12/20Includes: 2 rubber rings, 2 spacers

Made of high-quality fiberglass-reinforced plastic with cast-in brass sleeve suitable for all wheels of the axle system 12/20. The axle mount can always be used when building trailers yourself if the total load does not exceed 45 kg and the base plate of the trailer is designed stiff enough. For higher loads, we recommend the stainless steel rigid axle (axle system 12/20). Mounting surface min. 50 x 60 mm 4 holes 6 / 6.5 mm, drilling distance 38 (B) + 25 mm (T) Delivery incl. 4 pressed in lock nuts stainless steel. Delivery without screws, as for DIY applications their length depend on the thickness and condition of the base plate

The extension axles extend the track width of our trailers by a total of 160mm if required (80mm on each side). They can be fitted to all smaller models of the chassis series (Hmini, Hmax, Hmax light, box trailers 73 liters and 115 liters) as well as to the H2O boat trailer. The load capacity with the axles extended decreases due to the then longer lever travel (except for the H2O which has other design features to compensate this). The set contains: 2x 21 cm long rigid axles stainless steel (axle system 12/20)  4x aluminum clamping block D20 with eccentric lever  8 countersunk screws Inox M6 x 16 (glue with Loctite!) Suitable for axle system 12/20 Weight: approx. 105 g

The extension axle extends the track width of the H2O-80 by a total of 160mm if required. The load capacity of the H2O is thereby increased in comparison to the axle mounts made of fibre-reinforced plastic due to the design. The set contains: 2x 21 cm long rigid axles stainless steel (axle system 12/20) 4x aluminum clamping block D20 with eccentric lever 8 countersunk screws Inox M6 x 16 (glue with Loctite!) Suitable for axle system 12/20 Weight: approx. 105 g

The extension axles extend the track width of the H2O/66 by a total of 260mm if required. The load capacity of the H2O is thereby increased in comparison to the axle mounts made of fibre-reinforced plastic due to the design. The set contains: 2x 32 cm long rigid axles stainless steel (axle system 12/20) 4x aluminum clamping block D20 with eccentric lever 8 countersunk screws Inox M6 x 16 (glue with Loctite!) Suitable for axle system 12/20 Weight: approx. 125 g

The extension axles extend the track width of the H2O/66 by a total of 260mm if required. The load capacity of the H2O is thereby increased in comparison to the axle mounts made of fibre-reinforced plastic due to the design. The set contains: 2x 32 cm long rigid axles stainless steel (axle system 12/20) 4x aluminum clamping block D20 with eccentric lever 8 countersunk screws Inox M6 x 16 (glue with Loctite!) Suitable for axle system 12/20 Weight: approx. 125 g

Description For all those who would like to build their own bicycle trailer, we offer our rigid axle made of stainless steel in various lengths. We recommend this continuous axle for all bicycle trailers that are loaded with more than 45 kg. The axle distributes the load symmetrically over both wheels and also stiffens the entire trailer construction. It minimises the force transferred to the base plate of the trailer, resulting in less deformation and fewer vibrations during the ride. Technical data Material: Stainless steel Inner diameter: 12 mm Outer diameter: 20 mm Scope of delivery Stainless steel rigid axle Compatibility The stainless steel rigid axle can be bolted under the trailer with two D20 aluminium clamping blocks (axle system 12/20). The stainless steel rigid axle is compatible with all our 12/20 axle system wheels. The stainless steel rigid axle is compatible with all our 12 mm thru axles of the 12/20 axle system. Assembly instructions Please note that the rigid axle cannot be cut to length yourself when building your own, as an axle mount with fine thread is firmly screwed and glued in on each side, with a right-hand thread on the right-hand side and a left-hand thread on the left-hand side. When building your own trailer, please note the installation direction of the axle (R = right in the direction of travel, L = left in the direction of travel). You should also select the axle length for your own construction so that approx. one centimetre protrudes on each side of the trailer so that the wheels do not rub against the base plate of the trailer (example: width of the base plate of the trailer: 63 cm, correct axle length: 65 cm). Further information Please also take a look at our DIY page and our Downloads page, where you will find additional information on building your own trailer.

Description For all those who would like to build their own bicycle trailer, we offer our rigid axle made of stainless steel in various lengths. We recommend this continuous axle for all bicycle trailers that are loaded with more than 45 kg. The axle distributes the load symmetrically over both wheels and also stiffens the entire trailer construction. It minimises the force transferred to the base plate of the trailer, resulting in less deformation and fewer vibrations during the ride. Technical data Material: Stainless steel Inner diameter: 12 mm Outer diameter: 20 mm Scope of delivery Stainless steel rigid axle Compatibility The stainless steel rigid axle can be bolted under the trailer with two D20 aluminium clamping blocks (axle system 12/20). The stainless steel rigid axle is compatible with all our 12/20 axle system wheels. The stainless steel rigid axle is compatible with all our 12 mm thru axles of the 12/20 axle system. Assembly instructions Please note that the rigid axle cannot be cut to length yourself when building your own, as an axle mount with fine thread is firmly screwed and glued in on each side, with a right-hand thread on the right-hand side and a left-hand thread on the left-hand side. When building your own trailer, please note the installation direction of the axle (R = right in the direction of travel, L = left in the direction of travel). You should also select the axle length for your own construction so that approx. one centimetre protrudes on each side of the trailer so that the wheels do not rub against the base plate of the trailer (example: width of the base plate of the trailer: 63 cm, correct axle length: 65 cm). Further information Please also take a look at our DIY page and our Downloads page, where you will find additional information on building your own trailer.

Description For all those who would like to build their own bicycle trailer, we offer our rigid axle made of stainless steel in various lengths. We recommend this continuous axle for all bicycle trailers that are loaded with more than 45 kg. The axle distributes the load symmetrically over both wheels and also stiffens the entire trailer construction. It minimises the force transferred to the base plate of the trailer, resulting in less deformation and fewer vibrations during the ride. Technical data Material: Stainless steel Inner diameter: 12 mm Outer diameter: 20 mm Scope of delivery Stainless steel rigid axle Compatibility The stainless steel rigid axle can be bolted under the trailer with two D20 aluminium clamping blocks (axle system 12/20). The stainless steel rigid axle is compatible with all our 12/20 axle system wheels. The stainless steel rigid axle is compatible with all our 12 mm thru axles of the 12/20 axle system. Assembly instructions Please note that the rigid axle cannot be cut to length yourself when building your own, as an axle mount with fine thread is firmly screwed and glued in on each side, with a right-hand thread on the right-hand side and a left-hand thread on the left-hand side. When building your own trailer, please note the installation direction of the axle (R = right in the direction of travel, L = left in the direction of travel). You should also select the axle length for your own construction so that approx. one centimetre protrudes on each side of the trailer so that the wheels do not rub against the base plate of the trailer (example: width of the base plate of the trailer: 63 cm, correct axle length: 65 cm). Further information Please also take a look at our DIY page and our Downloads page, where you will find additional information on building your own trailer.

Description For all those who would like to build their own bicycle trailer, we offer our rigid axle made of stainless steel in various lengths. We recommend this continuous axle for all bicycle trailers that are loaded with more than 45 kg. The axle distributes the load symmetrically over both wheels and also stiffens the entire trailer construction. It minimises the force transferred to the base plate of the trailer, resulting in less deformation and fewer vibrations during the ride. Technical data Material: Stainless steel Inner diameter: 12 mm Outer diameter: 20 mm Scope of delivery Stainless steel rigid axle Compatibility The stainless steel rigid axle can be bolted under the trailer with two D20 aluminium clamping blocks (axle system 12/20). The stainless steel rigid axle is compatible with all our 12/20 axle system wheels. The stainless steel rigid axle is compatible with all our 12 mm thru axles of the 12/20 axle system. Assembly instructions Please note that the rigid axle cannot be cut to length yourself when building your own, as an axle mount with fine thread is firmly screwed and glued in on each side, with a right-hand thread on the right-hand side and a left-hand thread on the left-hand side. When building your own trailer, please note the installation direction of the axle (R = right in the direction of travel, L = left in the direction of travel). You should also select the axle length for your own construction so that approx. one centimetre protrudes on each side of the trailer so that the wheels do not rub against the base plate of the trailer (example: width of the base plate of the trailer: 63 cm, correct axle length: 65 cm). Further information Please also take a look at our DIY page and our Downloads page, where you will find additional information on building your own trailer.

Description For all those who would like to build their own bicycle trailer, we offer our rigid axle made of stainless steel in various lengths. We recommend this continuous axle for all bicycle trailers that are loaded with more than 45 kg. The axle distributes the load symmetrically over both wheels and also stiffens the entire trailer construction. It minimises the force transferred to the base plate of the trailer, resulting in less deformation and fewer vibrations during the ride. Technical data Material: Stainless steel Inner diameter: 12 mm Outer diameter: 20 mm Scope of delivery Stainless steel rigid axle Compatibility The stainless steel rigid axle can be bolted under the trailer with two D20 aluminium clamping blocks (axle system 12/20). The stainless steel rigid axle is compatible with all our 12/20 axle system wheels. The stainless steel rigid axle is compatible with all our 12 mm thru axles of the 12/20 axle system. Assembly instructions Please note that the rigid axle cannot be cut to length yourself when building your own, as an axle mount with fine thread is firmly screwed and glued in on each side, with a right-hand thread on the right-hand side and a left-hand thread on the left-hand side. When building your own trailer, please note the installation direction of the axle (R = right in the direction of travel, L = left in the direction of travel). You should also select the axle length for your own construction so that approx. one centimetre protrudes on each side of the trailer so that the wheels do not rub against the base plate of the trailer (example: width of the base plate of the trailer: 63 cm, correct axle length: 65 cm). Further information Please also take a look at our DIY page and our Downloads page, where you will find additional information on building your own trailer.

Description For all those who would like to build their own bicycle trailer, we offer our rigid axle made of stainless steel in various lengths. We recommend this continuous axle for all bicycle trailers that are loaded with more than 45 kg. The axle distributes the load symmetrically over both wheels and also stiffens the entire trailer construction. It minimises the force transferred to the base plate of the trailer, resulting in less deformation and fewer vibrations during the ride. Technical data Material: Stainless steel Inner diameter: 12 mm Outer diameter: 20 mm Scope of delivery Stainless steel rigid axle Compatibility The stainless steel rigid axle can be bolted under the trailer with two D20 aluminium clamping blocks (axle system 12/20). The stainless steel rigid axle is compatible with all our 12/20 axle system wheels. The stainless steel rigid axle is compatible with all our 12 mm thru axles of the 12/20 axle system. Assembly instructions Please note that the rigid axle cannot be cut to length yourself when building your own, as an axle mount with fine thread is firmly screwed and glued in on each side, with a right-hand thread on the right-hand side and a left-hand thread on the left-hand side. When building your own trailer, please note the installation direction of the axle (R = right in the direction of travel, L = left in the direction of travel). You should also select the axle length for your own construction so that approx. one centimetre protrudes on each side of the trailer so that the wheels do not rub against the base plate of the trailer (example: width of the base plate of the trailer: 63 cm, correct axle length: 65 cm). Further information Please also take a look at our DIY page and our Downloads page, where you will find additional information on building your own trailer.

Description For all those who would like to build their own bicycle trailer, we offer our rigid axle made of stainless steel in various lengths. We recommend this continuous axle for all bicycle trailers that are loaded with more than 45 kg. The axle distributes the load symmetrically over both wheels and also stiffens the entire trailer construction. It minimises the force transferred to the base plate of the trailer, resulting in less deformation and fewer vibrations during the ride. Technical data Material: Stainless steel Inner diameter: 12 mm Outer diameter: 20 mm Scope of delivery Stainless steel rigid axle Compatibility The stainless steel rigid axle can be bolted under the trailer with two D20 aluminium clamping blocks (axle system 12/20). The stainless steel rigid axle is compatible with all our 12/20 axle system wheels. The stainless steel rigid axle is compatible with all our 12 mm thru axles of the 12/20 axle system. Assembly instructions Please note that the rigid axle cannot be cut to length yourself when building your own, as an axle mount with fine thread is firmly screwed and glued in on each side, with a right-hand thread on the right-hand side and a left-hand thread on the left-hand side. When building your own trailer, please note the installation direction of the axle (R = right in the direction of travel, L = left in the direction of travel). You should also select the axle length for your own construction so that approx. one centimetre protrudes on each side of the trailer so that the wheels do not rub against the base plate of the trailer (example: width of the base plate of the trailer: 63 cm, correct axle length: 65 cm). Further information Please also take a look at our DIY page and our Downloads page, where you will find additional information on building your own trailer.

Description For all those who would like to build their own bicycle trailer, we offer our rigid axle made of stainless steel in various lengths. We recommend this continuous axle for all bicycle trailers that are loaded with more than 45 kg. The axle distributes the load symmetrically over both wheels and also stiffens the entire trailer construction. It minimises the force transferred to the base plate of the trailer, resulting in less deformation and fewer vibrations during the ride. Technical data Material: Stainless steel Inner diameter: 12 mm Outer diameter: 20 mm Scope of delivery Stainless steel rigid axle Compatibility The stainless steel rigid axle can be bolted under the trailer with two D20 aluminium clamping blocks (axle system 12/20). The stainless steel rigid axle is compatible with all our 12/20 axle system wheels. The stainless steel rigid axle is compatible with all our 12 mm thru axles of the 12/20 axle system. Assembly instructions Please note that the rigid axle cannot be cut to length yourself when building your own, as an axle mount with fine thread is firmly screwed and glued in on each side, with a right-hand thread on the right-hand side and a left-hand thread on the left-hand side. When building your own trailer, please note the installation direction of the axle (R = right in the direction of travel, L = left in the direction of travel). You should also select the axle length for your own construction so that approx. one centimetre protrudes on each side of the trailer so that the wheels do not rub against the base plate of the trailer (example: width of the base plate of the trailer: 63 cm, correct axle length: 65 cm). Further information Please also take a look at our DIY page and our Downloads page, where you will find additional information on building your own trailer.

Description For all those who would like to build their own bicycle trailer, we offer our rigid axle made of stainless steel in various lengths. We recommend this continuous axle for all bicycle trailers that are loaded with more than 45 kg. The axle distributes the load symmetrically over both wheels and also stiffens the entire trailer construction. It minimises the force transferred to the base plate of the trailer, resulting in less deformation and fewer vibrations during the ride. Technical data Material: Stainless steel Inner diameter: 12 mm Outer diameter: 20 mm Scope of delivery Stainless steel rigid axle Compatibility The stainless steel rigid axle can be bolted under the trailer with two D20 aluminium clamping blocks (axle system 12/20). The stainless steel rigid axle is compatible with all our 12/20 axle system wheels. The stainless steel rigid axle is compatible with all our 12 mm thru axles of the 12/20 axle system. Assembly instructions Please note that the rigid axle cannot be cut to length yourself when building your own, as an axle mount with fine thread is firmly screwed and glued in on each side, with a right-hand thread on the right-hand side and a left-hand thread on the left-hand side. When building your own trailer, please note the installation direction of the axle (R = right in the direction of travel, L = left in the direction of travel). You should also select the axle length for your own construction so that approx. one centimetre protrudes on each side of the trailer so that the wheels do not rub against the base plate of the trailer (example: width of the base plate of the trailer: 63 cm, correct axle length: 65 cm). Further information Please also take a look at our DIY page and our Downloads page, where you will find additional information on building your own trailer.

Clamping block made of CNC machined aluminum, black anodized. Suitable for 20mm stainless steel axles and wheels of the axle system 12/20. Two alloy clamping blocks are needed to mount the rigid axle. Support surface min. 25 x 70 mm 2 threaded holes M6, drilling distance 38 mm (not centered in the support surface!) Weight: approx. 105 g

Thanks to the Quick-release axle our wheels can be removed from our trailers with just one click. At the end of the Quick-release axle are ball lock pins that can be unlocked by pushing in the end cap on the other side of the axle. Those ball lock pins expand into a small groove inside our axle mounts thus securely holding the wheel in place.Axle diameter: 12 mmTotal length: 125 mmWeight: approx. 100 gIncludes a plastic spacer and a rubber ring.Fits all our wheels axle mounts of the axle system 12/20Please note: The axle is made of hardened steel since this is stronger than stainless steel. Therefore it should be cleaned regularily from dirt and lubricated with a high quality lubricant like chain oil.

This is the heavy-duty version of the stainless steel axle with an even larger diameter of 25mm making it extremely robust. It should be paired with our heavy-duty wheel set and the 15mm quick-release thru axle. We recommend these parts for trailers that will be used heavily and to the absolut maximum.The stainless steel rigid axle distributes the trailers load evenly over both wheels and also stiffens the trailers base. It minimizes the force input into the chassis and thus causes less deformation and fewer vibrations when driving. The stainless steel axle is bolted under the trailer floor with two high-quality CNC-milled aluminum clamping blocks (not included). In the rigid axle, the wheels can be inserted or removed with a click, thanks to the quick-release thru axle system.Please note for self-built trailers that the stainless steel axle cannot be cut to length, as an axle mount with fine thread is firmly screwed in and glued on each side, right-hand side with right-hand thread, left-hand side with left-hand thread. You should also select the axle length for self-built trailers so that approx. one centimeter protrudes on each side of the trailer so that the wheels do not rub against the base plate of the trailer (example: width of the base plate of the trailer: 63 cm, correct axle length: 65 cm). Inner diameter: 15 mm Outside diameter: 25 mm Suitable for the axle and wheel system 15/25 Supplied without aluminum clamping blocks, please order these separately. When building your own trailer, please note the installation direction of the axle (R = in driving direction right, L= in driving direction left).

Clamping block made of CNC machined aluminum, black anodized. Suitable for 25mm stainless steel axles and wheels of the axle system 15/25. Two alloy clamping blocks are needed to mount the axle. Support surface min. 25 x 70 mm 2 threaded holes M6, drilling distance 38 mm (not centered in the support surface!) Weight: approx. 115 g

When ordered together with one of our trailers with heavy-duty equipment, the 8 most important screw connections (4x SL drawbar bracket, 2x axle clamping blocks each) are additionally equipped with original Nordlock washers. The original Nordlock washers ensure guaranteed long-term strength of the screw connections and reduce the service and maintenance intervals in the long term. All bolted connections on our trailers are either fitted with A2 lock nuts as standard or secured with threadlocking adhesive. Nevertheless, all screw connections on bicycles and trailers can loosen over time due to vibration. It is therefore necessary to check all screw connections regularly and retighten them if necessary. With the built-in Nordlock washers, these maintenance intervals are significantly reduced. If ordered individually (without trailer), the washers are supplied in a small bag.  Scope of delivery:  8 pcs. original Nordlock lock washers stainless steel NL6 ss (glued in pairs - installation only in pairs!)